Talented and dedicated School Staff Education provides professional development opportunities Facilities offered by the School Innovative research at the School

Mechanical Engineering (2012-2013)

Print

 

BEng. (Hons.) Mechanical Engineering

No.

Supervisor

Title

1

Prof. Dr. Kyaw Sein

Design of shell and tube heat exchanger as an intercooler for turbocharged marine engine

2

Design and performance of a hydraulic ram for water pumping in rural remote areas

3

Design of flat plate solar collector with plane reflector for maximum radiation as a source of renewable energy

4

Cooling load computation and duct design of pressurized cockpit air conditioning system for a single seater supersonic aircraft

5

Design of a single stage centrifugal blower for high pressure application

6

PM Dr. Ghulam Abdul Quadir

Design and analysis of a centrifugal pump

7

Performance analysis of gas turbine using steam injection in combustion chamber

8

Exergy analysis of a Gas Turbine Power Plant using simple Brayton cycle and also its modified version

9

An irreversible dual heat engine cycle’s optimum performance analysis

10

CFD analysis of square microchannel heat exchanger performance for different nanofluids under parallel flow configuration

11

PM Dr. Merdang Sembiring

Design and analysis of refrigerated container in high speed train

12

Expansion valve and evaporator of air conditioning solar energy

13

Design advice for choosing turbine penstock-piping system

14

Redesign and analysis of wet cooling tower

15

Design HAWT blades, application in Kangar

16

Azizul Mohamad

Thermal Modelling and Design of a CubeSat Satellite using MATLAB/Simulink

17

Thermal Analysis and Design Optimization of CubeSat Satellite using ANSYS/Fluent

18

Thermal Optimization of Proton Exchange Membrane Fuel Cell System in Fuel Cell Electric Vehicle using ANSYS/Fluent

19

Thermal Optimization of Direct Methanol Fuel Cell System for Portable Applications using ANSYS/Fluent

20

Designing a fuel cell powered mobile robot

21

Designing a solar powered cooling device for domestic applications

22

Dr. Zuradzman Mohamad Razlan

Study on gas-liquid flow behaviour in room air conditioner; comparison of R-134a flow and air-water flow

23

Development of a small wall mounted room air conditioner for an ordinary room

24

Review and study on energy efficiency standard requirement of Malaysia for room air conditioner

25

Study on relation of 3 blade propeller fan to mouth-ring gap on performance of air flow volume and sound level

26

Development of a stratified flow generating device for air-water flow

27

Development of an annular mist flow generating device for air-water flow

28

Anas Abdul Rahman

The study of high altitude Wind Power: Ideal design for capturing kinetic energy of high altitude winds

29

The study of high altitude Wind Power: Methods of converting kinetic energy to other form of energy

30

Motion powered charging device

31

Thermoelectric cooking pot for charging small electrical devices

32

A noble way of cooling down the car interior during hot day using thermoelectric cooling

33

Mohd Ridzuan Mohd Jamir

Investigation of empty fruit bunch (EFB) bio oil as lubricant in cold forward extrusion

34

The effect of taper die angle in cold forward extrusion

35

The effect of micro-pits on the extrusion die surface

36

The plasticity flow analysis of extrusion process

37

Design and development of smart home clothes dryer prototype through energy efficient air heating

38

Tan Wee Choon

Experimental measurement of instantaneous flow velocities using Particle Image Velocimetry (PIV)

39

Analysis of static hole error for pressure measurement

40

Optimization on the usage of electrical heater to minimize the operating cost within speaker production

41

Analysis of laboratory scale micro jet turbine

42

Analysis of plate heat exchanger

43

Dr. Rakhmad Arief Siregar

Numerical and experimental analysis of thin plat perforation

44

Side door beam crashworthiness optimization

45

Stiffness analysis of Cube Satellite frame

46

Vibration analysis of Cube Satellite frame

47

Mechanism design of door and hinges of Picosatellite Orbital Deployer (POD)

48

Dr. Shahriman Abu Bakar

River feasibility study on the implementation of integrated Irrigation gate monitoring and control system

49

Experimental analysis on the vibration effect of length of a satellite panel due to attitude maneuvering

50

Experimental analysis on the vibration effect of width of a†satellite panel due to attitude manoeuvring

51

Intelligent robot for smart intruder detection system

52

Biomechanics study on lower back end effects on human working posture

53

Intelligent wheel chair drive for stoke patient

54

The vein graft monitoring device after surgery procedure

55

Computational analysis on upper extremity vein graft: Pulsatile blood flow simulation on straight, mismatched end-to-end and kinked vein grafts

56

Dr. Zol Bahri Razali

Redesign and analysis of a sorting blade for automated size-based sorting device

57

Enhance design and analyses on automated manipulator for ferrous and non-ferrous industrial wastes

58

Design, analysis and fabrication of robotic arm for sorting of multi-materials

59

Analysis of mechanical properties for arm and elbow parts of glass handling robotic arm

60

Reprogramming the articulated robotic arm by using Programmable Logic Controller (PLC)

61

Dr. Mohd Shukry Abdul Majid

Shear response modelling of glass fibre reinforced epoxy (GRE) laminates using ANSYS

62

Damage cumulative model of multiaxial ultimate elastic wall stress (UEWS) test using Miner’s Law

63

Interlaminar shear stress (ILSS) test of glass fibre reinforced epoxy (GRE) under elevated temperatures

64

Effects of aging in interlaminar shear stress (ILSS) test of GRE laminate

65

Compression yielding of epoxy resin - strain rate and temperature effect

66

Effects of curing level on elastic behaviour of pure epoxy resin

67

Effects of winding angle in interlaminar shear stress (ILSS) test of GRE laminate

68

Dr. Haftirman

An experimental analysis of fatigue crack growth of aluminum alloy under random loading

69

Effect of the thickness on fatigue crack growth

70

An investigation of a three bending test on air craft sandwich panels

71

Fatigue crack initiation and growth of aluminum alloy with stress ratio effects

72

Prototype of cotton machine: Remove cotton process

73

Prototype of cotton machine: Thread cotton process

74

Mechanisms of fatigue crack growth in aluminum alloys

75

Dr. Mohd Afendi Rojan

Fatigue strength of ductile adhesive single lap dissimilar joint in chassis of racing sports car: effect of overlap length

76

Stress analysis of adhesive bonding of urea granulator fluidization bed

77

Stress and thermal analysis of CubeSAT structure

78

Prototype of compact flexural testing

79

Effect of diameter and mechanical endurance analysis on piston for 1.3 liters Campro IAFM engine

80

Fracture of ductile adhesive arcan joint bonded with dissimilar adherends: effect of bond thickness and loading conditions

81

Fatigue analysis of adhesive dissimilar joint: Effect of bond thickness

82

Shah Fenner Khan Mohamad Khan

CAED of biomaterials plate for use in mandibular fracture

83

Numerical analysis of cellular structures for mandibular implant

84

Design of a monitoring system for control of temperature and pressure in a desktop size constant pressure sintering machine

85

Design of a press mechanism in a desktop size constant pressure sintering machine

86

Reverse engineering and refesign of biomaterials fracture plate for use in bone fracture

87

Redesign and fabrication of molten deposition modelling based additive manufacturing machine: Designing new extruder head

88

Redesign and fabrication of molten deposition modelling based additive manufacturing machine: Designing the automatic build platform (ABP)

89

Muhamad Safwan Muhamad Azmi

Design and development for ergonomic durian peeling machine (DPM)

90

Design and development for human arm assist

91

Thermal effect on aluminium deformation behaviour

92

Heat treatment effects on mild steel

93

Design and development of an optimum illumination dome for eco-day lighting system

94

Imaduddin Helmi Wan Nordin

Finite element analysis on effect of case depth on residual stresses of case-carburized spur gear

95

Experimental analysis on effect of case depth on fatigue strength of case-carburized mild steel

96

Experimental analysis on fatigue strength of weld joint

97

Finite element analysis on residual stresses in cold forging process

98

Experimental analysis on fatigue strength of rivet joint

99

Mohd Hafis Sulaiman

Performance of lubrication in cold work drawing process: Effects of surface roughness on friction

100

Development of lubricant from palm-oil based empty fruit bunch wastes

101

Performance of lubrication in cold work drawing process: Effects of lubricant quantity on wear

102

Surface coating for metal-to-metal surface contact application: Effects of scratch on friction

103

Effects of heat transfer on the performance of thermoelectric refrigeration system

 

 

To find out more about research on the campus in detail you can visit us in ResearchGate (URL: https://www.researchgate.net/plugins. DepartmentPluginConfig. html?institutionKey=Universiti_ Malaysia_Perlis&departmentKey= School_of_Mechatronic_Engineering)
Tab content 2

School of Mechatronic Engineering
Universiti Malaysia Perlis (UniMAP)
Kampus Pauh Putra
02600 Arau, Perlis
MALAYSIA
Tel: +604-988 5166 , Fax: +604-988 5167

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Copyright © UniMAP
Security Policy | Privacy Policy |
Disclaimer | Copyright

logo1 unimap logo2 jata malaysia logo3 kpt logo4 msc logo5 MQA logo7 sqa logo6 qs

Wednesday the 29th. © 2015. School of Mechatronic Engineering UniMAP. Best viewed using Firefox or Chrome with 1280x768 resolution. | Home | Joomla 3 Templates Joomlaskins
View My Stats